Omnisistem OnyxPro 101 Bedienungsanleitung

Tel: 253-395-9500 Fax: 253-395-9494 6403 South 208th Street, Kent, WA 98032KEEPTHISMANUALFORFUTURENEEDS 1 of 27

DMX512connection/connectionbetweenfixturesPleasenote,thestartingaddressdependsuponwhichcontrollerisbeingused.OnlyuseaDMXc

ConnectionwiththeMainsConnectthedevicetothepowersourcewiththeenclosedpowersupplycable.Theconfigurationoftheconnectioncablesis

Note:Afterswitchingon,thedevicewillautomaticallydetectwhetherDMX512dataisreceivedornot.IfthereisnodatareceivedattheDMXinpu

32-223 224-255 4 6 Shutter Shutter Closed No Function (Shutter Open) Strobe Effect (Slow to Fast) No Function (Shutter Open) Pulse Effect in Sequen

215-255 0-27 28-255 9 12 Virtual Color 2 Color Bounce: Blackout Red Green Blue White Red=0, Green=Up, Blue=Full, White=0 Red=0, Green=Full, Blue=

Continuous Positioning 0-360° 0-255 10 12 Gobos Indexed: Position 1 (Open) Position 2 - Position 8 Indexed w/ Blackout: Position 1 (Open) Posit

19 26 Fixed Gobo Indexed & Indexed w/ Blackout & Shake: Position 1 (Open) Position 2 - Position 8 Forward Wheel Spin (Stop to Fast) Revers

Pulse Closing w/ Reverse Blackout No Function 64-95 96-255 25 32 Iris Indexed: Max Diameter to Min Diameter Pulse Opening & Pulse Closing: Pul

unitoff.(Activatesafter5minutes.)LampAdjust①Pan…...AdjustValueInformationTimeInfoCurrentXXXX(Hours)FixtureLifeXXXX(Hours)Boot

PasswordXXXPrivateReload(③)On/OffAllReloadOn/OffPassword(050)PrivateReloadAllReloadPr

Everypersoninvolvedwiththeinstallation,operationandmaintenanceofthisdeviceneedsto● bequalified● followtheinstructionsofthismanu

InitialstatusWiththisfunctionyoucandisplaywhichvaluetherespectivechannelswillstart.ErrorchannelsWiththisfunctionyoucandisplay

3. PresstheEnterbuttontoconfirm.HibernationPowerStandbyModeWith this function you can put the device in the power standby mode. This fun

Category_NetworkManagementDISC_UNIQUE_BRANCH0x0001DISC_MUTE0x0002DISC_UN_MUTE0x0003CategoryRDMInformationSUPPORTED_PARAMETERS0x0050P

RESET_DEVICE0x1001ReloadDefaultWiththisfunctionyoucanrestorethefactorysettingsofthedevice.Thedifferentsettings(markedinthetabl

3. Select “Sequence” by pressing Up or Down. 4. Press the Enter-button to confirm. 5. Press Up or Down to select “Master” or “Alone”. The selection &

ErrorMessagesWhen you turn on the fixture, it will perform a reset first. The display may show an error message                

Werecommendafrequentcleaningofthedevice.Pleaseuseamoist,lintfreecloth.Neverusealcoholorsolvents!Theobjectivelenswillrequire

TECHNICALSPECIFICATIONSPowerSupply:100240VAC,~50/60HzPowerConsumption:180WDMXControlChannels:26/33/17/18DMX512Connection:3pinXL

(SafetyInstructionsContinued)● If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch   

OPERATINGPROCEDURESThisdeviceisamovingheadlightforcreatingdecorativeeffects.Thisproductisonlyallowedtobeoperatedwithanalternat

PRODUCTFEATURES&SPECIFICATIONSLight● Lightsource:LumiEnginCOB21600MW● Lamplife:60,000hours● LuminousFlux:8450lumen,11300lu

OVERVIEW(1) Objectivelens(2) Arm(3) Base (4) Handle(5)Wirelessindicator(6) Display(7) Microphone(8) Leftbutton(9) Downbutton(10

INSTALLATIONInserting/ExchangingGobosIfyouwishtouseothergobos,orifgobosaretobeexchanged,pleasefollowtheinstructionsbelow:Remov

Procedure:Theprojectorshouldbeinstalledoutsideareaswherepersonsmaywalkbyorbeseated.IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EX

Themanufacturercannotbemadeliablefordamagescausedbyincorrectinstallationsorinsufficientsafetyprecautions!Installthesafetybondby